Bauder Flat Roof Navigator

Bauder lightweight green roof construction, specifically for lightweight roof constructions. Weight of the entire system in a saturated state only about 75 kg/m².

• Vegetation (sedum planting)
• LBB-E vegetation soil, 5 cm
• Bauder FV 125 filter fleece
• Bauder WSP 50 water storage panel
• Bauder FSM 600 protection mat

Please refer to the product data sheet for further technical data.

» Detailed information on Bauder green roof systems

Elastomer bitumen torch-on membrane, root resistance according to FLL guidelines.

• Installation: torch-on application
• Slate on the top (green), foil on the underside
• Polyester fleece reinforcement 250 g/m²
• Length 5 m, width 1 m
• Thickness 5.2 mm
• Cold bending -36 °C
• Heat resistance +120 °C
• Elongation 45 %

Please refer to the product data sheet for further technical data.

Cold self-adhesive first layer made of special elastomer bitumen with variable lap adhesion: Cold adhesion in the lap area and on the surface in the area of the cold bonding and welding of longitudinal and lateral laps. The required type of lap connection can be determined on site at any time and changed again.

• Cold self-adhesive installation, torch-on application (lap)
• Foil on the top; release film and cold self-adhesive compound on the underside
• Reinforcement as a mesh scrim with glass mat
• Length 7.5 m, width 1 m
• Thickness 3.5 mm
• Cold bending at top ≤-25 °C, at bottom ≤-30 °C
• Heat resistance ≥+100 °C
• Elongation ≥2 %

Please refer to the product data sheet for further technical data.

Insulation panels in a triangular shape cut from the insulating block, without lap.
For application as a cross slope on flat roof insulation between the drainage points. 

• Panel size per triangular shape LES 1 to LES 10 (1 m to 10 m)
• Fire behaviour: class E according to DIN EN 13501-1B2 according to DIN 4102-1
• Compressive strength > 120 kPa (> 0.12 N/mm²)
• Thermal conductivity (D) 0.030

Please refer to the product data sheet for further technical data.

Flat roof insulation panels with aluminium facing on both sides, with lap.

• BauderPIR FA panel size: 2400 x 1,200 mm
• Fire behaviour: class E according to DIN EN 13501-1B2 according to DIN 4102-1
• Compressive strength ≥120 kPa (≥0.12 N/mm²)
• Thermal conductivity (Germany) 0.023
  Thermal conductivity (EU) 0.022
• PIR index > 250

Please refer to the product data sheet for further technical data.

Moisture-curing insulation material adhesive for bonding suitable insulation materials to substrates, such as BauderTEC vapour barrier membranes, bitumen membranes with surfacing granules or concrete or BauderPIR. Bauder foam adhesive cannot be used with non-lined synthetic membranes.

Please refer to the product data sheet for further technical data.

Slated elastomer bitumen torch-on membrane as a vapour barrier membrane

• Installation: torch-on application
• Natural slate with centre strips on the top
• Underside: Foil
• Reinforcement as an aluminium polyester combination with glass mat
• Length 5 m, width 1 m
• Thickness 3.7 mm
• Cold bending ≤ -20 °C
• Heat resistance ≥ +70 °C
• sd-value ≥ 1500 m

Please refer to the product data sheet for further technical data.

Bitumen primer for improving the adhesion of bitumen membranes. Bauder Burkolit V is applied to the entire surface with rollers, spray equipment or brushes. The substrate should be sufficiently dry and free of frost (+5°C surface of the substrate). Not suitable for indoor areas or, for example, foundation pits as it contains solvents.

Please refer to the product data sheet for further technical data.

Bauder lightweight green roof construction, specifically for lightweight roof constructions. Weight of the entire system in a saturated state only about 75 kg/m².

• Vegetation (sedum planting)
• LBB-E vegetation soil, 5 cm
• Bauder FV 125 filter fleece
• Bauder WSP 50 water storage panel
• Bauder FSM 600 protection mat

Please refer to the product data sheet for further technical data.

» Detailed information on Bauder green roof systems

Root-resistant polymer bitumen torch-on membrane with an extremely resilient polyester-compound reinforcement inlay combined with a premium bitumen formulation.

• Installation: torch-on application
• Green-white slate on the top, foil on the underside
• Polyester composite reinforcement 300 g/m²
• Length 5 m, width 1 m
• Thickness 5.2 mm
• Cold bending -25 °C at top / -40 °C at bottom
• Heat resistance +150 °C at top / +120 °C at bottom
• Elongation 23 %

Please refer to the product data sheet for further technical data.


ALTERNATIVE PRODUCTS
Other capping sheets can also be used in this construction instead of BauderSMARAGD:

• BauderPLANT E Product data sheet

These membranes made of special elastomer bitumen are particularly impressive thanks to their minimal heating time – made possible by the THERMAL strips on the underside. Due to the low heat development, BauderPIR insulation materials are not damaged. At the same time, you save energy, material and time. The sanded zones between the THERMAL strips ensure controlled vapour pressure relief if humidity is accidentally trapped. This prevents the formation of bubbles and blisters.

• Installation: high-speed application
• Fleece-laminated and sand on the top; foil and thermal strips on the underside
• Reinforcement as polyester fibre with glass mat 180 g/m²
• Length 7.5 m, width 1 m
• Thickness 4.2 mm
• Cold bending ≤-30 °C
• Heat resistance ≥+100 °C
• Elongation ≥20 %

Please refer to the product data sheet for further technical data.

Insulation panels in a triangular shape cut from the insulating block, without lap.
For application as a cross slope on flat roof insulation between the drainage points. 

• Panel size per triangular shape LES 1 to LES 10 (1 m to 10 m)
• Fire behaviour: class E according to DIN EN 13501-1B2 according to DIN 4102-1
• Compressive strength > 120 kPa (> 0.12 N/mm²)
• Thermal conductivity (D) 0.030

Please refer to the product data sheet for further technical data.

Flat roof insulation panels with two-sided facing made of mineral fleece.

• Panel size 1200 x 800 mm
• Available with/without lap
• Fire behaviour: class E according to DIN EN 13501-1B2 according to DIN 4102-1
• Compressive strength ≥120 kPa (≥0.12 N/mm²)
• Thermal conductivity (Germany) 0.028 (<80 mm)/0.027 (≥80 mm)/0.026 (≥120 mm)
  Thermal conductivity (EU) 0.027 (<80 mm)/0.026 (≥80 mm)/0.025 (≥120 mm)
• PIR index > 250

Please refer to the product data sheet for further technical data.

Moisture-curing insulation material adhesive for bonding suitable insulation materials to substrates, such as BauderTEC vapour barrier membranes, bitumen membranes with surfacing granules or concrete or BauderPIR. Bauder foam adhesive cannot be used with non-lined synthetic membranes.

Please refer to the product data sheet for further technical data.

Fast-torchable elastomer bitumen vapour barrier membrane with thermal strips on both sides

• Installation: high-speed application
• Foil and thermal strips on the top
• Underside: Foil, thermal strips
• Reinforcement as an aluminium polyester combination with glass mat
• Length 7.5 m, width 1.08 m
• Thickness 4 mm
• Cold bending ≤ -10 °C
• Heat resistance ≥ +70 °C
• sd-value ≥ 1500 m

Please refer to the product data sheet for further technical data.

Bitumen primer for improving the adhesion of bitumen membranes. Bauder Burkolit V is applied to the entire surface with rollers, spray equipment or brushes. The substrate should be sufficiently dry and free of frost (+5°C surface of the substrate). Not suitable for indoor areas or, for example, foundation pits as it contains solvents.

Please refer to the product data sheet for further technical data.

Bauder lightweight green roof construction, specifically for lightweight roof constructions. Weight of the entire system in a saturated state only about 75 kg/m².

• Vegetation (sedum planting)
• LBB-E vegetation soil, 5 cm
• Bauder FV 125 filter fleece
• Bauder WSP 50 water storage panel
• Bauder FSM 600 protection mat

Please refer to the product data sheet for further technical data.

» Detailed information on Bauder green roof systems

Root-resistant polymer bitumen torch-on membrane with an extremely resilient polyester-compound reinforcement inlay combined with a premium bitumen formulation.

• Installation: torch-on application
• Green-white slate on the top, foil on the underside
• Polyester composite reinforcement 300 g/m²
• Length 5 m, width 1 m
• Thickness 5.2 mm
• Cold bending -25 °C at top / -40 °C at bottom
• Heat resistance +150 °C at top / +120 °C at bottom
• Elongation 23 %

Please refer to the product data sheet for further technical data.


ALTERNATIVE PRODUCTS
Other capping sheets can also be used in this construction instead of BauderSMARAGD:

• BauderPLANT E Product data sheet

Special elastomer roof waterproofing membrane as a first layer in a BauderKOMPAKT system

• Installation: pour and roll-in application
• Foil on the top, longitudinal lap sanded, underside sanded
• Polyester fleece reinforcement
• Length 10 m, width 1 m
• Cold bending at top ≤-25
• Heat resistance ≥+100
• Elongation ≥35

Please refer to the product data sheet for further technical data.

Flat roof insulation panels without facing for the Bauder PIR Compact Roof.

• Panel size 600 x 600 mm
• Top with slope, also available as flat panels
• Fire behaviour: class E according to DIN EN 13501-1B2 according to DIN 4102-1
• Compressive strength ≥150 kPa (≥0.15 N/mm²)
• Thermal conductivity (Germany) 0.028 (<80 mm)/0.027 (≥80 mm)/0.026 (≥120 mm)
  Thermal conductivity (EU) 0.027 (<80 mm)/0.026 (≥80 mm)/0.025 (≥120 mm)
• PIR index > 250

Please refer to the product data sheet for further technical data.

Special elastomer bitumen vapour barrier membrane fur the BauderKOMPAKT system

• Installation: pour and roll-in application
• Top mica; underside mica
• Reinforcement as an aluminium polyester combination with glass mat
• Length 10 m, width 1 m
• Thickness 2.5 mm
• Cold bending at top ≤-25
• Heat resistance ≥+70
• Elongation ≥2
• sd-value ≥1500

Please refer to the product data sheet for further technical data.

Bitumen primer for improving the adhesion of bitumen membranes. Bauder Burkolit V is applied to the entire surface with rollers, spray equipment or brushes. The substrate should be sufficiently dry and free of frost (+5°C surface of the substrate). Not suitable for indoor areas or, for example, foundation pits as it contains solvents.

Please refer to the product data sheet for further technical data.

Standard green roof construction, for roof constructions with a normal/high load bearing capacity. Weight of the entire system in a saturated state about 125 kg/m². 

• Vegetation (sedum planting, sedum/herb planting)
• LBB-E vegetation soil, 8 cm
• Bauder FV 125 filter fleece
• Bauder DSE 20/1 drainage and water retention layer
• Bauder FSM 600 protection mat

If the drainage and water retention layer is filled with 2-5 mm of gravel, this creates a stable basis for the construction of walk-on paving with pressure-resistant insulation materials (e.g. BauderPIR).

Please refer to the product data sheet for further technical data.

Detailed information on Bauder green roof systems

Elastomer bitumen torch-on membrane, root resistance according to FLL guidelines.

• Installation: torch-on application
• Slate on the top (green), foil on the underside
• Polyester fleece reinforcement 250 g/m²
• Length 5 m, width 1 m
• Thickness 5.2 mm
• Cold bending -36 °C
• Heat resistance +120 °C
• Elongation 45 %

Please refer to the product data sheet for further technical data.

Cold self-adhesive first layer made of special elastomer bitumen with variable lap adhesion: Cold adhesion in the lap area and on the surface in the area of the cold bonding and welding of longitudinal and lateral laps. The required type of lap connection can be determined on site at any time and changed again.

• Cold self-adhesive installation, torch-on application (lap)
• Foil on the top; release film and cold self-adhesive compound on the underside
• Reinforcement as a mesh scrim with glass mat
• Length 7.5 m, width 1 m
• Thickness 3.5 mm
• Cold bending at top ≤-25 °C, at bottom ≤-30 °C
• Heat resistance ≥+100 °C
• Elongation ≥2 %

Please refer to the product data sheet for further technical data.

Insulation panels in a triangular shape cut from the insulating block, without lap.
For application as a cross slope on flat roof insulation between the drainage points. 

• Panel size per triangular shape LES 1 to LES 10 (1 m to 10 m)
• Fire behaviour: class E according to DIN EN 13501-1B2 according to DIN 4102-1
• Compressive strength > 120 kPa (> 0.12 N/mm²)
• Thermal conductivity (D) 0.030

Please refer to the product data sheet for further technical data.

Flat roof insulation panels with aluminium facing on both sides, with lap.

• BauderPIR FA panel size: 2400 x 1,200 mm
• Fire behaviour: class E according to DIN EN 13501-1B2 according to DIN 4102-1
• Compressive strength ≥120 kPa (≥0.12 N/mm²)
• Thermal conductivity (Germany) 0.023
  Thermal conductivity (EU) 0.022
• PIR index > 250

Please refer to the product data sheet for further technical data.

Moisture-curing insulation material adhesive for bonding suitable insulation materials to substrates, such as BauderTEC vapour barrier membranes, bitumen membranes with surfacing granules or concrete or BauderPIR. Bauder foam adhesive cannot be used with non-lined synthetic membranes.

Please refer to the product data sheet for further technical data.

Slated elastomer bitumen torch-on membrane as a vapour barrier membrane

• Installation: torch-on application
• Natural slate with centre strips on the top
• Underside: Foil
• Reinforcement as an aluminium polyester combination with glass mat
• Length 5 m, width 1 m
• Thickness 3.7 mm
• Cold bending ≤ -20 °C
• Heat resistance ≥ +70 °C
• sd-value ≥ 1500 m

Please refer to the product data sheet for further technical data.

Bitumen primer for improving the adhesion of bitumen membranes. Bauder Burkolit V is applied to the entire surface with rollers, spray equipment or brushes. The substrate should be sufficiently dry and free of frost (+5°C surface of the substrate). Not suitable for indoor areas or, for example, foundation pits as it contains solvents.

Please refer to the product data sheet for further technical data.

Standard green roof construction, for roof constructions with a normal/high load bearing capacity. Weight of the entire system in a saturated state about 125 kg/m². 

• Vegetation (sedum planting, sedum/herb planting)
• LBB-E vegetation soil, 8 cm
• Bauder FV 125 filter fleece
• Bauder DSE 20/1 drainage and water retention layer
• Bauder FSM 600 protection mat

If the drainage and water retention layer is filled with 2-5 mm of gravel, this creates a stable basis for the construction of walk-on paving with pressure-resistant insulation materials (e.g. BauderPIR).

Please refer to the product data sheet for further technical data.

Detailed information on Bauder green roof systems

Root-resistant polymer bitumen torch-on membrane with an extremely resilient polyester-compound reinforcement inlay combined with a premium bitumen formulation.

• Installation: torch-on application
• Green-white slate on the top, foil on the underside
• Polyester composite reinforcement 300 g/m²
• Length 5 m, width 1 m
• Thickness 5.2 mm
• Cold bending -25 °C at top / -40 °C at bottom
• Heat resistance +150 °C at top / +120 °C at bottom
• Elongation 23 %

Please refer to the product data sheet for further technical data.


ALTERNATIVE PRODUCTS
Other capping sheets can also be used in this construction instead of BauderSMARAGD:

• BauderPLANT E Product data sheet

These membranes made of special elastomer bitumen are particularly impressive thanks to their minimal heating time – made possible by the THERMAL strips on the underside. Due to the low heat development, BauderPIR insulation materials are not damaged. At the same time, you save energy, material and time. The sanded zones between the THERMAL strips ensure controlled vapour pressure relief if humidity is accidentally trapped. This prevents the formation of bubbles and blisters.

• Installation: high-speed application
• Fleece-laminated and sand on the top; foil and thermal strips on the underside
• Reinforcement as polyester fibre with glass mat 180 g/m²
• Length 7.5 m, width 1 m
• Thickness 4.2 mm
• Cold bending ≤-30 °C
• Heat resistance ≥+100 °C
• Elongation ≥20 %

Please refer to the product data sheet for further technical data.

Insulation panels in a triangular shape cut from the insulating block, without lap.
For application as a cross slope on flat roof insulation between the drainage points. 

• Panel size per triangular shape LES 1 to LES 10 (1 m to 10 m)
• Fire behaviour: class E according to DIN EN 13501-1B2 according to DIN 4102-1
• Compressive strength > 120 kPa (> 0.12 N/mm²)
• Thermal conductivity (D) 0.030

Please refer to the product data sheet for further technical data.

Flat roof insulation panels with two-sided facing made of mineral fleece.

• Panel size 1200 x 800 mm
• Available with/without lap
• Fire behaviour: class E according to DIN EN 13501-1B2 according to DIN 4102-1
• Compressive strength ≥120 kPa (≥0.12 N/mm²)
• Thermal conductivity (Germany) 0.028 (<80 mm)/0.027 (≥80 mm)/0.026 (≥120 mm)
  Thermal conductivity (EU) 0.027 (<80 mm)/0.026 (≥80 mm)/0.025 (≥120 mm)
• PIR index > 250

Please refer to the product data sheet for further technical data.

Fast-torchable elastomer bitumen vapour barrier membrane with thermal strips on both sides

• Installation: high-speed application
• Foil and thermal strips on the top
• Underside: Foil, thermal strips
• Reinforcement as an aluminium polyester combination with glass mat
• Length 7.5 m, width 1.08 m
• Thickness 4 mm
• Cold bending ≤ -10 °C
• Heat resistance ≥ +70 °C
• sd-value ≥ 1500 m

Please refer to the product data sheet for further technical data.

Bitumen primer for improving the adhesion of bitumen membranes. Bauder Burkolit V is applied to the entire surface with rollers, spray equipment or brushes. The substrate should be sufficiently dry and free of frost (+5°C surface of the substrate). Not suitable for indoor areas or, for example, foundation pits as it contains solvents.

Please refer to the product data sheet for further technical data.

Standard green roof construction, for roof constructions with a normal/high load bearing capacity. Weight of the entire system in a saturated state about 125 kg/m². 

• Vegetation (sedum planting, sedum/herb planting)
• LBB-E vegetation soil, 8 cm
• Bauder FV 125 filter fleece
• Bauder DSE 20/1 drainage and water retention layer
• Bauder FSM 600 protection mat

If the drainage and water retention layer is filled with 2-5 mm of gravel, this creates a stable basis for the construction of walk-on paving with pressure-resistant insulation materials (e.g. BauderPIR).

Please refer to the product data sheet for further technical data.

Detailed information on Bauder green roof systems

Root-resistant polymer bitumen torch-on membrane with an extremely resilient polyester-compound reinforcement inlay combined with a premium bitumen formulation.

• Installation: torch-on application
• Green-white slate on the top, foil on the underside
• Polyester composite reinforcement 300 g/m²
• Length 5 m, width 1 m
• Thickness 5.2 mm
• Cold bending -25 °C at top / -40 °C at bottom
• Heat resistance +150 °C at top / +120 °C at bottom
• Elongation 23 %

Please refer to the product data sheet for further technical data.


ALTERNATIVE PRODUCTS
Other capping sheets can also be used in this construction instead of BauderSMARAGD:

• BauderPLANT E Product data sheet

Special elastomer roof waterproofing membrane as a first layer in a BauderKOMPAKT system

• Installation: pour and roll-in application
• Foil on the top, longitudinal lap sanded, underside sanded
• Polyester fleece reinforcement
• Length 10 m, width 1 m
• Cold bending at top ≤-25
• Heat resistance ≥+100
• Elongation ≥35

Please refer to the product data sheet for further technical data.

Flat roof insulation panels without facing for the Bauder PIR Compact Roof.

• Panel size 600 x 600 mm
• Top with slope, also available as flat panels
• Fire behaviour: class E according to DIN EN 13501-1B2 according to DIN 4102-1
• Compressive strength ≥150 kPa (≥0.15 N/mm²)
• Thermal conductivity (Germany) 0.028 (<80 mm)/0.027 (≥80 mm)/0.026 (≥120 mm)
  Thermal conductivity (EU) 0.027 (<80 mm)/0.026 (≥80 mm)/0.025 (≥120 mm)
• PIR index > 250

Please refer to the product data sheet for further technical data.

Special elastomer bitumen vapour barrier membrane fur the BauderKOMPAKT system

• Installation: pour and roll-in application
• Top mica; underside mica
• Reinforcement as an aluminium polyester combination with glass mat
• Length 10 m, width 1 m
• Thickness 2.5 mm
• Cold bending at top ≤-25
• Heat resistance ≥+70
• Elongation ≥2
• sd-value ≥1500

Please refer to the product data sheet for further technical data.

Bitumen primer for improving the adhesion of bitumen membranes. Bauder Burkolit V is applied to the entire surface with rollers, spray equipment or brushes. The substrate should be sufficiently dry and free of frost (+5°C surface of the substrate). Not suitable for indoor areas or, for example, foundation pits as it contains solvents.

Please refer to the product data sheet for further technical data.

The new BauderSOLAR UK FD is designed for use on large connected roof areas. The roof substructure is installed without perforating the roof waterproofing and is also ideal for roofs with low load reserves.

• Safe, penetration-free installation
• 12° pitch
• Weight of roof substructure approx. 5 kg
• Dimensions (L x W x H): 1450 x 330 x 310 mm

» Detailed information about BauderSOLAR photovoltaic systems

Polymer bitumen torch-on membrane with extremely resilient polyester composite reinforcement inlay combined with a premium bitumen formulation. Slate coating in the colours green-white and graphite black.

• Installation: torch-on application
• Slate on the top, foil on the underside
• Polyester composite reinforcement 300 g/m²
• Length 5 m, width 1 m
• Thickness 5.2 mm
• Cold bending -25 °C at top / -40 °C at bottom
• Heat resistance +150 °C at top / +120 °C at bottom
• Elongation 23 %

Please refer to the product data sheet for further technical data.


ALTERNATIVE PRODUCTS
Other capping sheets can also be used in this construction instead of BauderKARAT:

• Baukubit K 5 K Product data sheet

Elastomer bitumen torch-on membrane

• Installation: Torch-on application
• Top mica, foil on the underside
• Glass fabric reinforcement
• Length 5 m
• Width 1 m
• Thickness 4 mm
• Cold bending  ≤ -30 °C
• Heat resistance ≥ +110 °C
• Elongation ≥ 2

Please refer to the product data sheet for further technical data.

Insulation panels in a triangular shape cut from the insulating block, without lap.
For application as a cross slope on flat roof insulation between the drainage points. 

• Panel size per triangular shape LES 1 to LES 10 (1 m to 10 m)
• Fire behaviour: class E according to DIN EN 13501-1B2 according to DIN 4102-1
• Compressive strength > 120 kPa (> 0.12 N/mm²)
• Thermal conductivity (D) 0.030

Please refer to the product data sheet for further technical data.

Flat roof insulation panels with two-sided facing made of mineral fleece.

• Panel size 1200 x 800 mm
• Available with/without lap
• Fire behaviour: class E according to DIN EN 13501-1B2 according to DIN 4102-1
• Compressive strength ≥120 kPa (≥0.12 N/mm²)
• Thermal conductivity (Germany) 0.028 (<80 mm)/0.027 (≥80 mm)/0.026 (≥120 mm)
  Thermal conductivity (EU) 0.027 (<80 mm)/0.026 (≥80 mm)/0.025 (≥120 mm)
• PIR index > 250

Please refer to the product data sheet for further technical data.

Fast-torchable elastomer bitumen vapour barrier membrane with thermal strips on both sides

• Installation: high-speed application
• Foil and thermal strips on the top
• Underside: Foil, thermal strips
• Reinforcement as an aluminium polyester combination with glass mat
• Length 7.5 m, width 1.08 m
• Thickness 4 mm
• Cold bending ≤ -10 °C
• Heat resistance ≥ +70 °C
• sd-value ≥ 1500 m

Please refer to the product data sheet for further technical data.

Bitumen primer for improving the adhesion of bitumen membranes. Bauder Burkolit V is applied to the entire surface with rollers, spray equipment or brushes. The substrate should be sufficiently dry and free of frost (+5°C surface of the substrate). Not suitable for indoor areas or, for example, foundation pits as it contains solvents.

Please refer to the product data sheet for further technical data.

The new BauderSOLAR UK FD is designed for use on large connected roof areas. The roof substructure is installed without perforating the roof waterproofing and is also ideal for roofs with low load reserves.

• Safe, penetration-free installation
• 12° pitch
• Weight of roof substructure approx. 5 kg
• Dimensions (L x W x H): 1450 x 330 x 310 mm

» Detailed information about BauderSOLAR photovoltaic systems

Polymer bitumen torch-on membrane with extremely resilient polyester composite reinforcement inlay combined with a premium bitumen formulation. Slate coating in the colours green-white and graphite black.

• Installation: torch-on application
• Slate on the top, foil on the underside
• Polyester composite reinforcement 300 g/m²
• Length 5 m, width 1 m
• Thickness 5.2 mm
• Cold bending -25 °C at top / -40 °C at bottom
• Heat resistance +150 °C at top / +120 °C at bottom
• Elongation 23 %

Please refer to the product data sheet for further technical data.


ALTERNATIVE PRODUCTS
Other capping sheets can also be used in this construction instead of BauderKARAT:

• Baukubit K 5 K Product data sheet

Special elastomer roof waterproofing membrane as a first layer in a BauderKOMPAKT system

• Installation: pour and roll-in application
• Foil on the top, longitudinal lap sanded, underside sanded
• Polyester fleece reinforcement
• Length 10 m, width 1 m
• Cold bending at top ≤-25
• Heat resistance ≥+100
• Elongation ≥35

Please refer to the product data sheet for further technical data.

Flat roof insulation panels without facing for the Bauder PIR Compact Roof.

• Panel size 600 x 600 mm
• Top with slope, also available as flat panels
• Fire behaviour: class E according to DIN EN 13501-1B2 according to DIN 4102-1
• Compressive strength ≥150 kPa (≥0.15 N/mm²)
• Thermal conductivity (Germany) 0.028 (<80 mm)/0.027 (≥80 mm)/0.026 (≥120 mm)
  Thermal conductivity (EU) 0.027 (<80 mm)/0.026 (≥80 mm)/0.025 (≥120 mm)
• PIR index > 250

Please refer to the product data sheet for further technical data.

Special elastomer bitumen vapour barrier membrane fur the BauderKOMPAKT system

• Installation: pour and roll-in application
• Top mica; underside mica
• Reinforcement as an aluminium polyester combination with glass mat
• Length 10 m, width 1 m
• Thickness 2.5 mm
• Cold bending at top ≤-25
• Heat resistance ≥+70
• Elongation ≥2
• sd-value ≥1500

Please refer to the product data sheet for further technical data.

Bitumen primer for improving the adhesion of bitumen membranes. Bauder Burkolit V is applied to the entire surface with rollers, spray equipment or brushes. The substrate should be sufficiently dry and free of frost (+5°C surface of the substrate). Not suitable for indoor areas or, for example, foundation pits as it contains solvents.

Please refer to the product data sheet for further technical data.

Bauder lightweight green roof construction, specifically for lightweight roof constructions. Weight of the entire system in a saturated state only about 75 kg/m².

• Vegetation (sedum planting)
• LBB-E vegetation soil, 5 cm
• Bauder FV 125 filter fleece
• Bauder WSP 50 water storage panel
• Bauder FSM 600 protection mat

Please refer to the product data sheet for further technical data.

» Detailed information on Bauder green roof systems

FPO-PP synthetic roofing membrane, which is reinforced with synthetic fabric and lined additionally on the underside with synthetic fibre fleece. In addition to the proven characteristics of fibre-reinforced membranes, the lamination allows the membrane to be adhered securely to withstand wind uplift with the help of PU adhesive.

• Application: bonded
• Installation: hot-air torch-on application
• Pearl white or silver grey on the top, (white) fleece on the underside
• PES fabric reinforcement
• Length 20 m
• Width 1.5 m
• Thickness 1.5/1.8/2.0 mm (+ 2 mm fleece in each case)

Please refer to the product data sheet for further technical data.

Moisture-curing adhesive for bonding fleece-laminated roofing membranes directly to approved substrates: BauderPIR FA, BauderPIR M, EPS, laminated mineral fibre insulation, bitumen or concrete with a primer. Bauder membrane adhesive cannot be used with non-laminated synthetic membranes.

Please refer to the product data for further technical data.

Flat roof insulation panels with aluminium facing on both sides, with lap.

• BauderPIR FA panel size: 2400 x 1,200 mm
• Fire behaviour: class E according to DIN EN 13501-1B2 according to DIN 4102-1
• Compressive strength ≥120 kPa (≥0.12 N/mm²)
• Thermal conductivity (Germany) 0.023
  Thermal conductivity (EU) 0.022
• PIR index > 250

Please refer to the product data sheet for further technical data.

Moisture-curing insulation material adhesive for bonding suitable insulation materials to substrates, such as BauderTEC vapour barrier membranes, bitumen membranes with surfacing granules or concrete or BauderPIR. Bauder foam adhesive cannot be used with non-lined synthetic membranes.

Please refer to the product data sheet for further technical data.

Finely coated special elastomer bitumen vapour barrier torch-on membrane

• Installation: torch-on application
• Top mica with lap strips, foil on the underside
• Reinforcement as an aluminium-polyester combination with special reinforcement
• Length 5 m, width 1 m
• Thickness 4 mm
• Cold bending ≤ -30 °C
• Heat resistance ≥ +110 °C
• sd-value ≥ 1500 m

Please refer to the product data sheet for further technical data.

Bitumen primer for improving the adhesion of bitumen membranes. Bauder Burkolit V is applied to the entire surface with rollers, spray equipment or brushes. The substrate should be sufficiently dry and free of frost (+5°C surface of the substrate). Not suitable for indoor areas or, for example, foundation pits as it contains solvents.

Please refer to the product data sheet for further technical data.